3 interconnect solutions http://www.3m.com/interconnects/ 3m is a trademark of 3m company. for technical, sales or ordering information call 800-225-5373 3m ? metpak ? cp2 press-fit header 2 mm type c, 55 signal cont acts, left guidance cp2 series physical mechanical electrical environmental pcb data compactpci is a registered trademark of picmg-pc i industrial computer manufacturers group, inc. metpak is a trademark of 3m company. insulation material: glass filled polyester (pbt) insulation flammability: ul 94 v-0 contact material: copper alloy plating: see ordering information mating force: 0.75 n/contact maximum withdrawal force: 0.15 n/contact minimum insulation resistance: 10g (minimum) current ratings: 1a at +70 c test voltage: 750 v ac temperature ratings: -55 c to +125 c recommended pcb hole platings: cu: .0250 - .050 mm [.001 - .002 in.] and sn or sn/pb: <10 m [400 "] pcb thickness: 1.4 - 5.6 mm [.06 - .22 in.] press-in force: 26 6n/pin on nominal hole diameter ? 0.6 0.05 mm [? .024 .002 in.] retention force: 20 5n/pin on nominal hole diameter ? 0.6 0.05 mm [? .024 .002 in.] ts-2034-04 sheet 1 of 4 date modified: april 11, 2007 ? 25 mm basic system unit ? compactpci ? combines the benefits of pci desktop architecture with the ruggedness of the 3u and 6u ieee eurocard form factor popularized by the vme bus ? designed according to iec 61076-4-101 and iec 917 standards ? 2 mm grid spacing allows for high signal density at low cost ? ?eye of the needle? compliant pin press-fit design reduces manufacturing time and cost ? feed through termination available for midplane applications ? additional grounding rows available for improved ground bounce and emi immunity ? see regulatory inform ation appendix (ria) for chemical comp liance information ul file no.: e68080
3 interconnect solutions http://www.3m.com/interconnects/ 3m is a trademark of 3m company. for technical, sales or ordering information call 800-225-5373 3m ? metpak ? cp2 press-fit header 2 mm type c, 55 signal cont acts, left guidance cp2 series ts-2034-04 sheet 2 of 4 .0 .00 .000 mm 2.5 .25 .025 tolerance unless noted mm [inch] [ ] dimensions for reference only ? this diagram serves only for part number descriptive definitions. ? for standard product configurations please see following pages. please contact your local sales representative for customer specific product configurations. cp2 - hc055 - x x x - xxxx plating options: tg30 = 30 " [0.76 m] gold contact area 100 " [2.54 m] tin-lead terminal area 50 " [1.27 m] nickel underplate (ria e2 & c2 apply) g30 = 30 " [0.76 m] gold overall 50 " [1.27 m] nickel underplate (ria e1 & c1 apply) cp2-hsc055-x shroud (order separately) standoff height: 1 = 0.7 mm (4.0 mm pcb thickness) 2 = 1.5 mm (3.2 mm pcb thickness) 3 = 2.3 mm (2.4 mm pcb thickness) 4 = 3.1 mm (1.6 mm pcb thickness) emlb patterns grounding options: g = with ground pins blank = without ground pins primary tail length: 1 = 3.7 mm (plating tg30 only) 2 = 13 mm (plating g30 only) 3 = 14.5 mm (plating g30 only) 4 = 16 mm (plating g30 only) loading configurations (see diagrams on following pages.) ordering information e a b c d 1357911 15.40 .606 13.45 .530 12.00 .472 2.00 .079 tail length (see contact overview) mating length (see contact overview) 1.00 .039 max. f z 20.00 .787 2.00 .079 25.00 .984 max. (on sheet 4 of 4)
3 interconnect solutions http://www.3m.com/interconnects/ 3m is a trademark of 3m company. for technical, sales or ordering information call 800-225-5373 3m ? metpak ? cp2 press-fit header 2 mm type c, 55 signal cont acts, left guidance cp2 series cp2-hc055-e1-tg30 connector type c11 cp2-hc055-ge1-tg30 connector type c11 f f c c c c c c c c c c c e a a a a a a a a a a a e a a a a a a a a a a a d a a a a a a a a a a a d a a a a a a a a a a a c a a a a a a a a a a a c a a a a a a a a a a a b a a a a a a a a a a a b a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a z z c c c c c c c c c c c 1 2 3 4 5 6 7 8 9 10 11 1 2 3 4 5 6 7 8 9 10 11 cp2-hc055-a1-tg30 connector type c11 cp2-hc055-ga1-tg30 connector type c11 f f c c c c c c c c c c c e b b b b b b b b b b b e b b b b b b b b b b b d b b b b b b b b b b b d b b b b b b b b b b b c b b b b b b b b b b b c b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b a b b b b b b b b b b b a b b b b b b b b b b b z z c c c c c c c c c c c 1 2 3 4 5 6 7 8 9 10 11 1 2 3 4 5 6 7 8 9 10 11 cp2-hc055-f2-g30 connector type c11 cp2-hc055-gf2-g30 connector type c11 f f c c c c c c c c c c c e k k k k k k k k k k k e k k k k k k k k k k k d k k k k k k k k k k k d k k k k k k k k k k k c k k k k k k k k k k k c k k k k k k k k k k k b k k k k k k k k k k k b k k k k k k k k k k k a k k k k k k k k k k k a k k k k k k k k k k k z z c c c c c c c c c c c 1 2 3 4 5 6 7 8 9 10 11 1 2 3 4 5 6 7 8 9 10 11 CP2-HC055-GA4-G30 connector type c11 f t t t t t t t t t t t e r r r r r r r r r r r d r r r r r r r r r r r c r r r r r r r r r r r b r r r r r r r r r r r a r r r r r r r r r r r z t t t t t t t t t t t 1 2 3 4 5 6 7 8 9 10 11 ts-2034-04 sheet 3 of 4
3 interconnect solutions http://www.3m.com/interconnects/ 3m is a trademark of 3m company. for technical, sales or ordering information call 800-225-5373 3m ? metpak ? cp2 press-fit header 2 mm type c, 55 signal cont acts, left guidance cp2 series f e d c b a z 1 2 3 4 5 6 7 8 9 10 11 ts-2034-04 sheet 4 of 4 signal contact configuration worksheet recommended pcb hole mounting pattern connector side lo 0.10 a b c d e f 11 9 7 5 3 1 20.00 .787 3.00 .118 o .60 .05 .024 .002 plated holes z o 2.00 +.05 0 .079 +.002 -.000 reference plane for plug in unit 12.00 .472 2.00 .079 3.70 .146 13.00 .512 14.50 .571 16.00 .630 5.20 .205 6.70 .264 8.20 .323 a bc klm np q rs t p2 r3 r2 r1 mating length tail length contact overview top surface of backplane
regulatory information appendix 3m electronic solutions division/interconnect europe appendix e1: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment, as amended by eu commission decision 2005/618/ec. this product is rohs compliant 2005/95/ec. rohs compliant 2005/95/ec means that the product or part (product) does not contain any of the substances in excess of the maximum concentration values in eu directive 2002/95/ec, as amended by commission decision 2005/618/ ec, unless the substance is in an application that is exempt under eu rohs. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix e2: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment, as amended by eu commission decision 2005/618/ec this product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under eu commission decision 2005/747/ec. rohs compliant 2005/95/ec means that the product or part (product) does not contain any of the substances in excess of the maximum concentration values in eu directive 2002/95/ec, as amended by commission decision 2005/618/ ec, unless the substance is in an application that is exempt under eu rohs. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix e3: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment as amended by commission decision 2005/618/ec. this product contains lead in the solder tail area in excess of the maximum concentration value allowed. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix e4: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment, as amended by eu commission decision 2005/618/ec. this product contains decabde in the insulating material in excess of the maximum concentration value allowed but is compliant by exemption under eu commission decision 2005/17/ec. rohs compliant 2005/95/ec means that the product or part (product) does not contain any of the substances in excess of the maximum concentration values in eu directive 2002/95/ec, as amended by commission decision 2005/618/ec, unless the substance is in an application that is exempt under eu rohs. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. ria-2217-b
china appendix c1: china rohs electronic industry standard of the peoples republic of china, sj/t11363-2006, requirements for concentration limits for certain hazardous substances in electronic information products. this symbol, per marking for the control of pollution caused by electronic information products, sj/t11364-2006, means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix c2: china rohs 2 0 electronic industry standard of the peoples republic of china, sj/t11363-2006, requirements for concentration limits for certain hazardous substances in electronic information products. this symbol, per marking for the control of pollution caused by electronic information products, sj/t11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. the numerical reference in the symbol above should not be construed as a representation regarding the products life or an extension of a product warranty. the product warranty is stated below. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the product warranty stated below. important notice all statements, technical information, and recommendations related to 3ms products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. before using this product, you must evaluate it and determine if it is suitable for your intended application. you assume all risks and liability associated with such use. any statements related to the product which are not contained in 3ms current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3m. warranty; limited remedy; limited liability. this product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3m makes no other warranties including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose. if this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3ms option, to replace or repair the 3m product or refund the purchase price of the 3m product. except where prohibited by law, 3m will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3m product, regardless of the legal theory asserted. 3 electronic solutions division 6801 river place blvd. austin, tx 78726-9000 800/225-5373 www.3m.com/interconnects ria-2217-b ? 3m 2007 name and content of hazardous substances or elements
|
